Then, check if YouTube works again on the device. If YouTube still refuses to work, then move on to the next solution. If restarting Xbox One does not work, then reset Xbox One. Doing a hard reset will not cause data loss, and here is how to do that:. So, give it a try to see whether it is likewise helpful to you. Now check if the issue is fixed. If you have a metal sticker are care about the warranty, read below. If you have one of the new paper stickers, there is no effective way to remove it without Microsoft knowing.
Metal Film Trick For a metal-film sticker a hair-dryer can be used on high for about seconds to make this adhesive melt, and peel off the sticker carefully and slowly with a razor blade to remove the sticker without leaving behind the metal residue. This trick can be useful for having a system that has been opened repaired by Microsofts repair service. I've heard of many users who have attempted to fix a RRoD themselves and failed, if a DVD drive is modified with iXtreme a user can reflash it to stock, and as long as the sticker is intact the very rushed employees at Microsoft's repair centers aren't likely to check for other minor signs of tampering.
There are a large number of screws to be removed. I suggest cutting a long strand of duct tape to stick your pieces to, so during reassembly the console can go back together smoothly. View the pictures below to determine screw locations. Firstly, remove the DVD eject button by inserting a small flat-head screwdriver in between the DVD drive and the eject buttons base. Casing Screws The top shell is attached to the chassis though the use of six T10 Torx screws.
They are highlighted in red in the picture below. DVD Removal Once the six casing screws are removed, flip the console right side up and lift off the upper shell. You should be careful with the DVD drive power cable as the connector is fragile and wires can be torn out, so grab all the black wires as close to the connector as possible, and forcefully wiggle the connector out. At the front of the DVD drive there are two friction clips, which prevent movement and rattling.
Also lift up the metal tape that holds the drive to the chassis. Lift out the drive and place the friction clips on the duct tape roll. Motherboard Screws These screws are highlighted in green in the picture below. These connect different pieces of the motherboard to the chassis. They are about 1" long, bronze colored, and have a round top. Unscrew them all with your T10 Torx screwdriver and place them on the tape roll. Heatsink Screws For these final eight screws, highlighted in blue, tilt the console to a vertical position.
We do not want to remove the screws while the system is upside down, as the weight of the heatsinks on the final screws could have enough stress to crack some traces. With the console vertical, remove the final eight screws with your T8 and set the console right-side up. It is held in place by the fan housing itself. Insert a flat-head screwdriver into its lock point and pull off the shroud, it will take some wiggling to remove.
Remove the fan power cable from the motherboard. Finally, lift up on the metal tap above the fans, and pull the fan casing towards the front of the console. Lift it out and set it to the side. Wireless board The ring of light and wireless antenna is attached to this board on the front of the console. There are three T8 screws, with one underneath the white diffusion clip.
This clip disperses the light for players Pop off the bottom of the clip with a flat-head screwdriver, and the third screw will be revealed. Place these screws on the duct tape roll. You can now pull the wireless board off of the console.
If anything ever happens to your wireless board, a replacement or spare wireless board is exchangeable between Xbox s Unlike DVD drives which are ID'd to the motherboard. Motherboard It is time to remove the final piece. Grab the motherboard by the GPU heatsink short and wide and lift out the front first. Remove out the entire board and you have access to the entire system. Insert your screwdriver into the top section of the grille that's on the back of the console and twist it until the bracket unhooks, then repeat this process all the way down the side of the console.
Once all of the brackets are unhooked, the back part of the Xbox One's casing will pop open. Do not pull the casing off of the console yet. Doing so will break the ribbon that connects the front of your Xbox One to the circuit board.
Swing the top of the casing up. Make sure the Xbox One is sitting flat with its bottom face-down when you do this. The top of the casing should swing up and over, coming to rest at a 90 degree angle to the console's body. Unplug the front panel ribbon cable. Find the front of the cable, which will be near the "On" button for the console's face plate. Once you find it, pull the blue tab that's wrapped around the connector up, then gently tug the cable to the left.
This will disconnect the cable from the top of the casing. Pull the top of the casing away from the Xbox One's body. You should be able to do this without any resistance, since all of the connectors are now unhooked. Set the casing aside in a safe, dry place. Disconnect the speaker and Wi-Fi wires. There should be two wires connecting the top of the console to the front of the console; unplug these from the front of the console by gently pulling on them.
Unscrew the Wi-Fi card. Use a Torx T8 screwdriver to do this. Remove the Wi-Fi card. Pull the card straight up from underneath. This will unplug the Wi-Fi card from the Xbox One's internal circuit board. Set the Wi-Fi card aside in the same place as the top of the Xbox One's casing. Remove the screws from the metal case. Use your T9 and T10 Torx screwdrivers for this. The metal case is the last piece of the Xbox One that you need to remove in order to open it. There are eight total screws to remove; you'll see a light "C" with a number next to or below the screws.
Two of the screws are at the bottom of the fan box. Make sure you place the discarded screws in a plastic bag so that you don't lose them. Gently open the metal case. Hold the fan corner of the case and pry it up diagonally so that the cable in the adjacent corner isn't damaged. If you feel resistance at any point, set the case down and try again.
Unplug the cable. This is the cable that attaches the Wi-Fi card to the console's circuitry. Gently tug the cable's connector, which is white, away from the off-white port into which it's plugged. This will completely detach the top of the metal case from the Xbox One. Popular Xbox Videos. Tenchi Ryu RetroArch-Pub. Easily find all your Xbox clips and screenshots. Just search for your gamertag above! Download Xbox game videos, share to social media, convert to gif, edit xbox clips and more.
Popular Xbox Screenshots. What are Xbox clips? Xbox clips are videos recorded on your Xbox One or Xbox Scarlett which range in length from 30 seconds to 10 minutes and p to 4k How do I record an Xbox clip? Capture your best gaming moments with an epic xbox clip or screenshot! Where are my Xbox clips? Yes How do I share my Xbox clips on Twitter? How do I share my Xbox clips on YouTube?
0コメント